Sintrol Process Dust Monitor | S303

Sintrol - Process Dust Monitor | S303

Supplier: ProDetec

Process Dust Monitor | S303

Perfect for installation after any filtration system or in common line channels leading into the emissions points of a plant.

In Stock

Product Features:

Continuous trend monitor that gives plant operators to see the performance of the filtration systems and ducts over a period of time. Perfect for installation after any filtration system or in common line channels leading into the emissions points of a plant.
State of the art Inductive Electrification principle minimises the need for maintenance on the dust monitor and provides an accurate trend for end users. 4-20mA output combined with an easy to use auto-setup feature that takes less than 30 minutes from installation makes the device both convenient and reliable.
Sintrol dust monitors are based on a unique Inductive Electrification technology. The measurement is based on particles interacting with an isolated probe mounted into the duct or stack. When moving particles pass nearby or hit the probe a signal is induced. This signal is then processed through a series of Sintrol’s advanced algorithms to filter out the noise and provide the most accurate dust measurement output.
Classic triboelectric technology is based on the DC signal, which is caused by particles making contact with the sensor to transfer charges. Compared to DC based measurements, the Inductive Electrification technology is more sensitive and minimizes the influence of sensor contamination, temperature drift and velocity changes. By using the Inductive Electrification technology, it is possible to reach dust concentration measurement thresholds as low as 0.01 mg/m3.

Technical Specifications:

Measurement Objects	Total Suspended Particles (TSP)
Measurement Range	Detection Limit 0.01 mg/m³ Maximum Range up to several g/m³, depending on conditions
Measurement Principle	Inductive Electrification
Protection Code	IP66
Power Supply Requirements	24 V DC ±10 % 100 … 240 V AC ±10%, 50 / 60 Hz
Power Consumption	Up to 10 W DC / AC
Output Signals	2 × Independent SPDT dry contact relays, max. 30 V DC / 5 A or 240 V AC / 5 A, cos φ = 1 Isolated active 4 … 20 mA output loop*, max. loop resistance 250 Ω
Communication Interface	Serial communication RS-485 USB Radio Frequency (RF, Requires optional RF antenna)
Communication Protocol	Modbus RTU (RS-485) Sintrol network with (USB, RF and RS-485)

To contact ProDetec about Sintrol Process Dust Monitor | S303 use Get a quote.

Product Features:

Continuous trend monitor that gives plant operators to see the performance of the filtration systems and ducts over a period of time. Perfect for installation after any filtration system or in common line channels leading into the emissions points of a plant.
State of the art Inductive Electrification principle minimises the need for maintenance on the dust monitor and provides an accurate trend for end users. 4-20mA output combined with an easy to use auto-setup feature that takes less than 30 minutes from installation makes the device both convenient and reliable.
Sintrol dust monitors are based on a unique Inductive Electrification technology. The measurement is based on particles interacting with an isolated probe mounted into the duct or stack. When moving particles pass nearby or hit the probe a signal is induced. This signal is then processed through a series of Sintrol’s advanced algorithms to filter out the noise and provide the most accurate dust measurement output.
Classic triboelectric technology is based on the DC signal, which is caused by particles making contact with the sensor to transfer charges. Compared to DC based measurements, the Inductive Electrification technology is more sensitive and minimizes the influence of sensor contamination, temperature drift and velocity changes. By using the Inductive Electrification technology, it is possible to reach dust concentration measurement thresholds as low as 0.01 mg/m3.

Technical Specifications:

Measurement Objects	Total Suspended Particles (TSP)
Measurement Range	Detection Limit 0.01 mg/m³ Maximum Range up to several g/m³, depending on conditions
Measurement Principle	Inductive Electrification
Protection Code	IP66
Power Supply Requirements	24 V DC ±10 % 100 … 240 V AC ±10%, 50 / 60 Hz
Power Consumption	Up to 10 W DC / AC
Output Signals	2 × Independent SPDT dry contact relays, max. 30 V DC / 5 A or 240 V AC / 5 A, cos φ = 1 Isolated active 4 … 20 mA output loop*, max. loop resistance 250 Ω
Communication Interface	Serial communication RS-485 USB Radio Frequency (RF, Requires optional RF antenna)
Communication Protocol	Modbus RTU (RS-485) Sintrol network with (USB, RF and RS-485)